Home

SV08-34-05
Solenoid Valve, 4-way, 3-position, Spool Type
230 bar [3300 psi] • 12 l/min [3.2 US gpm]

CV10-NP
Check Valve, Standard Direction
350 bar [5000 psi] • 80 l/min [21 US gpm]
DESCRIPTION AND OPERATION
This is a check valve where free flow takes place from port 1 to 2 and is blocked from port 2 to 1

Using Danfoss Genuine Parts you can guarantee maximum reliability of your equipment, maximizing productivity and performance. By using non-original spare parts you will save on cost but a negative impact on the performance and strength of your equipment.
Function: M13 DIN 43650

Using Danfoss Genuine Parts you can guarantee maximum reliability of your equipment, maximizing productivity and performance. By using non-original spare parts you will save on cost but a negative impact on the performance and strength of your equipment.
Function: R13 Deutsch

Using Danfoss Genuine Parts you can guarantee maximum reliability of your equipment, maximizing productivity and performance. By using non-original spare parts you will save on cost but a negative impact on the performance and strength of your equipment.
Function: M16 Deutsch

Using Danfoss Genuine Parts you can guarantee maximum reliability of your equipment, maximizing productivity and performance. By using non-original spare parts you will save on cost but a negative impact on the performance and strength of your equipment.
Function: M16 DIN 43650

Using Danfoss Genuine Parts you can guarantee maximum reliability of your equipment, maximizing productivity and performance. By using non-original spare parts you will save on cost but a negative impact on the performance and strength of your equipment.

Using Danfoss Genuine Parts you can guarantee maximum reliability of your equipment, maximizing productivity and performance. By using non-original spare parts you will save on cost but a negative impact on the performance and strength of your equipment.

Solenoid Valve, 2-way, Poppet Type, Normally Closed, Pilot Operated with Reverse Free Flow.
This is a 2-way, 2-position, poppet type, pilot operated, normally closed solenoid valve. In its de-energized condition, flow passes from port 1 to 2 but is blocked in the opposite direction. When energized, flow passes from port 2 to 1 and from 1 to 2. Some models have the option of a filter at port 2. Due to the low leakage provided by the poppet design, these valves can be used to hold loads in position or to interrupt a pressure line where flow normally passes in both directions. 

Solenoid Valve, 3-way, 2-position, Spool Type
230 bar [3300 psi] • 35 l/min [9 US gpm]
This is a 3-way, 2-position, spool type, direct acting solenoid valve. In the de-energized condition, port 1 is open to port 2 and port 3 is blocked. When energized, port 3 is open to port 1 and  port 2 is blocked. These valves can be used in normally open, normally closed or selector modes. They come standard with a push pin manual override. Always check the operating envelope to make sure the valve will work under the required application conditions.

Using Danfoss Genuine Parts you can guarantee maximum reliability of your equipment, maximizing productivity and performance. By using non-original spare parts you will save on cost but a negative impact on the performance and strength of your equipment.

CV10-NP
Check Valve, Standard Direction
350 bar [5000 psi] • 80 l/min [21 US gpm]
DESCRIPTION AND OPERATION
This is a check valve where free flow takes place from port 1 to 2 and is blocked from port 2 to 1

Solenoid Valve, 4-way, 2-position, Spool Type
230 bar [3300 psi] • 35 l/min [9 US gpm]
This is a 4-way, 2-position, spool type, direct acting solenoid valve. In the de-energized, condition port 3 is open to 2 and port 4 to 1. When energized port 3 is open to 4 and port 2 to 1. These valves are used to control the movement of cylinders or motors able to reverse the motion. Always check the  operating envelope to make sure the valve will work under the required application conditions. Port 1 is not intended for use as an inlet (Tank only).

Flow Divider/Combiner, Fixed Ratio, Flow Synchronizing Option 
210 bar [3000 psi] • 45 l/min [12 US gpm]
This is a fixed ratio flow divider/combiner valve. In dividing mode, flow enters port 3 and passes across two fixed orifices in linked spools. If the pressure drop through one orifice is higher than the other, then the spools will move together to restrict the flow in the lower pressure outlet port. This maintains  equal pressure drops across the spools, thus maintaining the flow division in the outlet ports. In combining mode, flow will enter ports 2 and 4 pass  through the orifices, which causes the spools to move to restrict the higher-pressure inlet and maintain equal pressure drops and equal flow into the  valve.

Using Danfoss Genuine Parts you can guarantee maximum reliability of your equipment, maximizing productivity and performance. By using non-original spare parts you will save on cost but a negative impact on the performance and strength of your equipment.
Function: M16 DIN 43650

SVP08-CDB
Solenoid Valve, 2-way, Poppet Type, Normally Closed, Direct Acting, Double Blocking
230 bar [3300 psi] • 25 l/min [6.6 US gpm]
This is a 2-way, 2-position, poppet type, direct acting, normally closed, bi-directional solenoid valve. In its de-energized condition, flow is blocked in both directions. Leakage in either direction is kept to a minimum due to the poppet design. When energized, flow can take place from port 2 to 1 and from 1 to 2. These valves come standard with a push pin manual override. These valves can be used to hold loads in position or interrupt a pressure line where flow is expected to pass in both directions in the de-energized condition. They do not suffer from momentary opening due to shock pressures.

Using Danfoss Genuine Parts you can guarantee maximum reliability of your equipment, maximizing productivity and performance. By using non-original spare parts you will save on cost but a negative impact on the performance and strength of your equipment.

Using Danfoss Genuine Parts you can guarantee maximum reliability of your equipment, maximizing productivity and performance. By using non-original spare parts you will save on cost but a negative impact on the performance and strength of your equipment.

Using Danfoss Genuine Parts you can guarantee maximum reliability of your equipment, maximizing productivity and performance. By using non-original spare parts you will save on cost but a negative impact on the performance and strength of your equipment.

Using Danfoss Genuine Parts you can guarantee maximum reliability of your equipment, maximizing productivity and performance. By using non-original spare parts you will save on cost but a negative impact on the performance and strength of your equipment.

PVG 32
Controllo proporzionale della portata e della pressione 
Fino ad un massimo di 12 moduli 
Varie tipologie di comando (idraulico, manuale, elettrico)
Comandi CAN BUS (protocolli CAN OPEN e ISOBUS)
Peso contenuto 
*L’immagine è a scopo illustrativo.

PVG 32
Controllo proporzionale della portata e della pressione 
Fino ad un massimo di 12 moduli 
Varie tipologie di comando (idraulico, manuale, elettrico)
Comandi CAN BUS (protocolli CAN OPEN e ISOBUS)
Peso contenuto 
*L’immagine è a scopo illustrativo.

Pvg 32
Proportional flow and pressure control
Up to 12 modules
Various types of controls (hydraulic, manual, electric)
CAN BUS controls (CAN OPEN and ISOBUS protocols)
Reduced weight
*image for illustration purposes only

PVG 32
Proportional flow and pressure control
Up to 12 modules
Various types of controls (hydraulic, manual, electric)
CAN BUS controls (CAN OPEN and ISOBUS protocols)
Reduced weight