Hydraulic Valves

Pilot Operated Check Valve, Port 1 Pilot to Open
350 bar [5000 psi] 21 l/min [5.5 US gpm]
DESCRIPTION AND OPERATION
This is a pilot operated check valve where free flow takes place from port 2 to 3 and is blocked from port 3 to 2 until pilot pressure is applied to port 1

RV08-DR-1-E-XXX-B-00 - DANFOSS

Description: M16-24D-26W-DE 
Specification:
Duty cycle: 100% at 115% of rated voltage at 40°C [104°F]
Magnet wire insulation: (200°C)
Ambient temperature range: -20 to 40 °C [-4 to 104 °F]
Environmental protection rating: IP69K: DE IP67: AJ , AS, and M3 term IP65: FL and DN
Input voltage range: 85% to 115% of rated voltage
Temperature rise at 115% of rated voltage: 130°C [266°F] above ambient
AC coils require external rectier

12V DIN 43650
Using Danfoss Genuine Parts you can guarantee maximum reliability of your equipment, maximizing productivity and performance. By using non-original spare parts you will save on cost but a negative impact on the performance and strength of your equipment.

Coils and Electronics
R16 - 20W Robust Coil
PERFORMANCE DATA:
Duty cycle: 100% at 133% of rated voltage and 70°C [158° F]
Magnet wire insulation: 200°C [392° F]
Ambient temperature range: -40 to +70 °C [-40 to 158 °F]
Input voltage range: 75% to 133% of rated voltage

By using genuine Danfoss spare parts, you ensure maximum reliability for your equipment, maximizing productivity and performance.

SVP10-NO
Solenoid Valve, 2-way, Poppet Type, Normally Open, Pilot Operated
230 bar [3300 psi] • 80 l/min [21 US gpm]
This is a 2-way, 2-position, poppet type, pilot operated, normally open solenoid valve. In its de-energized condition, flow can take place from port 2 to 1 but is restricted in the other direction. When energized, flow can take place from port 1 to 2 but is blocked in the other direction. Leakage is kept to a minimum due to the poppet design. Some models have the option of a filter around port 2, and these come standard with a push pin manual override. These valves can be used to hold loads in position when energized or bypass excess oil to tank in a fail-safe way.

Solenoid Valve, 2-way, Poppet Type, Normally Closed, Pilot Operated
230 bar [3300 psi] • 80 l/min [21 US gpm]
This is a 2-way, 2-position, poppet type, pilot operated, normally closed solenoid valve. In its de-energized condition, flow passes from port 1 to 2 but is blocked in the opposite direction. When energized, flow passes from port 2 to 1 but is restricted in the opposite direction. Some models have the option of a filter at port 2. Due to the low leakage provided by the poppet design, these valves can be used to hold loads in position and bypass excess oil to tank. 

Description: NCS 06/0 

Relief Valve, Direct Acting, Poppet Type with Dampening
315 bar [4600 psi] • 40 l/min [11 US gpm]
DESCRIPTION AND OPERATION
This is a direct acting, poppet type relief valve that relieves from port 1 to 2. It features a highly damped poppet for smooth and stable response It can be used as a cost-effective main relief or to protect an actuator from over-pressurization.

Logic Element, Normally Closed, Spool Type, Pilot to Close
350 bar [5000 psi] • 150 l/min [40 US gpm]
DESCRIPTION AND OPERATION
This is a 3-ported, normally closed, pilot to close spool type logic element. By opening port 3 to tank, flow can pass from port 1 to port 2. Flow is blocked from port 1 to port 2 unless the pressure is high enough in port 1 to overcome the spring set pressure. Applying pressure to port 3 will increase the pressure required in port 1 to open the valve by a factor of 1 to 1. This valve is ideal for use as a pressure compensator, bypass valve, or a pilot to close valve in regenerative circuits

CV08-NP
Check Valve, Standard Direction
350 bar [5000 psi] • 38 l/min [10 US gpm]
DESCRIPTION AND OPERATION
This is a check valve where free flow takes place from port 1 to 2 and is blocked from port 2 to 1.

CV08-NP
Check Valve, Standard Direction
350 bar [5000 psi] • 38 l/min [10 US gpm]
DESCRIPTION AND OPERATION
This is a check valve where free flow takes place from port 1 to 2 and is blocked from port 2 to 1.

Solenoid Valve, 3-way, 2-position, Spool Type
230 bar [3300 psi] • 35 l/min [9 US gpm]
This is a 3-way, 2-position, spool type, direct acting solenoid valve. In the de-energized condition, port 1 is open to port 2 and port 3 is blocked. When energized, port 3 is open to port 1 and  port 2 is blocked. These valves can be used in normally open, normally closed or selector modes. They come standard with a push pin manual override. Always check the operating envelope to make sure the valve will work under the required application conditions.

Pilot Operated Check Valve, Port 1 Pilot to open with Drain
315 bar [4600 psi]  30 l/min [8 US gpm]
DESCRIPTION AND OPERATION
This is a pilot operated check valve with a separate drain. Free flow takes place from port 3 to 4 and is blocked from port 4 to 3 until pilot pressure is applied to port 1. Port 2 is drained to tank to remove any effect of pressure in port 3 affecting the pilot pressure required to keep the valve open.

Description: CP10-B-3-B 

Coils and Electronics
R16 - 20W Robust Coil
PERFORMANCE DATA:
Duty cycle: 100% at 133% of rated voltage and 70°C [158° F]
Magnet wire insulation: 200°C [392° F]
Ambient temperature range: -40 to +70 °C [-40 to 158 °F]
Input voltage range: 75% to 133% of rated voltage

Using Danfoss Genuine Parts you can guarantee maximum reliability of your equipment, maximizing productivity and performance. By using non-original spare parts you will save on cost but a negative impact on the performance and strength of your equipment.
Function: R13 Deutsch

Function: M13 DIN 43650
Specification:
Duty cycle: 100% at 115% of rated voltage at 40°C [104°F]
Magnet wire insulation: (200°C)
Ambient temperature range: -20 to 40 °C [-4 to 104 °F]
Environmental protection rating: IP69K: DE IP67: AJ , AS, and M3 term IP65: FL and DN
Input voltage range: 85% to 115% of rated voltage
Temperature rise at 115% of rated voltage: 130°C [266°F] above ambient
AC coils require external rectier

Coils and Electrnics
M19 - 22W Proportional Coil
PERFORMANCE DATA:
Magnet wire insulation: 200°C [392°F]
Maximum Continuous Current: 1.8 A [at 12V] 0.9 A [at 24V]
Ambient temperature range: -20 to 40°C [-4 to 104 °F]

Specification:
Duty cycle: 100% at 115% of rated voltage at 40°C [104°F]
Magnet wire insulation: (200°C)
Ambient temperature range: -20 to 40 °C [-4 to 104 °F]
Environmental protection rating: IP69K: DE IP67: AJ , AS, and M3 term IP65: FL and DN
Input voltage range: 85% to 115% of rated voltage
Temperature rise at 115% of rated voltage: 130°C [266°F] above ambient
AC coils require external rectier