Hydraulic Valves

Pilot Operated Check Valve, Port 1 Pilot to open with Drain
315 bar [4600 psi]  30 l/min [8 US gpm]
DESCRIPTION AND OPERATION
This is a pilot operated check valve with a separate drain. Free flow takes place from port 3 to 4 and is blocked from port 4 to 3 until pilot pressure is applied to port 1. Port 2 is drained to tank to remove any effect of pressure in port 3 affecting the pilot pressure required to keep the valve open.

Description: CP10-B-3-B 

Coils and Electronics
R16 - 20W Robust Coil
PERFORMANCE DATA:
Duty cycle: 100% at 133% of rated voltage and 70°C [158° F]
Magnet wire insulation: 200°C [392° F]
Ambient temperature range: -40 to +70 °C [-40 to 158 °F]
Input voltage range: 75% to 133% of rated voltage

Using Danfoss Genuine Parts you can guarantee maximum reliability of your equipment, maximizing productivity and performance. By using non-original spare parts you will save on cost but a negative impact on the performance and strength of your equipment.
Function: R13 Deutsch

Function: M13 DIN 43650
Specification:
Duty cycle: 100% at 115% of rated voltage at 40°C [104°F]
Magnet wire insulation: (200°C)
Ambient temperature range: -20 to 40 °C [-4 to 104 °F]
Environmental protection rating: IP69K: DE IP67: AJ , AS, and M3 term IP65: FL and DN
Input voltage range: 85% to 115% of rated voltage
Temperature rise at 115% of rated voltage: 130°C [266°F] above ambient
AC coils require external rectier

Coils and Electrnics
M19 - 22W Proportional Coil
PERFORMANCE DATA:
Magnet wire insulation: 200°C [392°F]
Maximum Continuous Current: 1.8 A [at 12V] 0.9 A [at 24V]
Ambient temperature range: -20 to 40°C [-4 to 104 °F]

Specification:
Duty cycle: 100% at 115% of rated voltage at 40°C [104°F]
Magnet wire insulation: (200°C)
Ambient temperature range: -20 to 40 °C [-4 to 104 °F]
Environmental protection rating: IP69K: DE IP67: AJ , AS, and M3 term IP65: FL and DN
Input voltage range: 85% to 115% of rated voltage
Temperature rise at 115% of rated voltage: 130°C [266°F] above ambient
AC coils require external rectier

Description: M16-110A-26W-DN
Specification:
Duty cycle: 100% at 115% of rated voltage at 40°C [104°F]
Magnet wire insulation: (200°C)
Ambient temperature range: -20 to 40 °C [-4 to 104 °F]
Environmental protection rating: IP69K: DE IP67: AJ , AS, and M3 term IP65: FL and DN
Input voltage range: 85% to 115% of rated voltage
Temperature rise at 115% of rated voltage: 130°C [266°F] above ambient
AC coils require external rectier

Coils and Electronics
R16 - 20W Robust Coil
PERFORMANCE DATA:
Duty cycle: 100% at 133% of rated voltage and 70°C [158° F]
Magnet wire insulation: 200°C [392° F]
Ambient temperature range: -40 to +70 °C [-40 to 158 °F]
Input voltage range: 75% to 133% of rated voltage

Description:  NCS 06/3

Description: NCS 04/2

Description: VLP12/P2-B-00
Logic Element Poppet, Double Blocking Closed, Vent to Open 315 bar [4600 psi] • 160 l/min [42 US gpm]
This is a 3-ported, normally closed, double blocking poppet type logic element, with port 1 connected to port 3 through an orifice. By opening port 3 to tank, flow can pass from port 1 to port 2 but not from port 2 to port 1. Closing port 3 will prevent the valve from opening from port 1 to port 2. The area ratio between port 1 and 3 is 1 to 1 and port 2 is balanced between the seat diameter and the seal poppet diameter. By controlling the flow or pressure out of port 3 the valve can be used as an on/ off valve or in a pressure control function.

Flow Control, Partially Adjustable, Pressure Compensated, Priority Type
315 bar [4600 psi] • 30 l/min [8 US gpm]
This is a partially adjustable, priority type, pressure compensated flow control valve, where the flow from port 3 will remain constant regardless of the pressure difference across the valve, while excess flow passes from port 1 to 2. Flow enters at port 1 and passes across a fixed orifice in the spool, which creates a pressure drop. This causes the spool to move back against the spring, which then restricts the outlet flow. Port 1 then opens to port 2 to allow excess flow to pass. The regulated flow will always take priority and remains constant if the working pressure is higher in either port 2 or port 3.

Free flow nose to side check valve
Capacity: 160 L/min. | Cavity: T-5A
Control: XCracking pressure: ASeal material: N
*Image for illustration purposes only

Pilot-to-open check valve with standard pilot
Capacity: 120 L/min. | Cavity: T-2A

Control: XAdjustment Range: CSeal Material: N

Pilot-operated, pressure-reducing/relieving valve with drain to port 4
Capacity: 80 L/min. | Cavity: T-22A
Control: LAdjustment range: ASeal material: N
*image for illustration purposes only

Single ball shuttle valve with signal at port 2
Capacity: 1.25 gpm | Cavity: T-163A
Control: X
Adjustment range: X
Seal material: N
*Image for illustration purposes only

Description: M16-110RA-22W-DN
Specification:
Duty cycle: 100% at 115% of rated voltage at 40°C [104°F]
Magnet wire insulation: (200°C)
Ambient temperature range: -20 to 40 °C [-4 to 104 °F]
Environmental protection rating: IP69K: DE IP67: AJ , AS, and M3 term IP65: FL and DN
Input voltage range: 85% to 115% of rated voltage
Temperature rise at 115% of rated voltage: 130°C [266°F] above ambient
AC coils require external rectier

Description: CP210-2-B-0-E-C-250
This is a pilot operated spool type relief valve that relieves pressure from 1 to 2.

Overcenter Valve, Standard, Direct Acting, Internal Drain, Port 3 Pilot
350 bar [5000 psi] • 19 l/min [5 US gpm]

Description: M16-12D-26W-AS
Specification:
Duty cycle: 100% at 115% of rated voltage at 40°C [104°F]
Magnet wire insulation: (200°C)
Ambient temperature range: -20 to 40 °C [-4 to 104 °F]
Environmental protection rating: IP69K: DE IP67: AJ , AS, and M3 term IP65: FL and DN
Input voltage range: 85% to 115% of rated voltage
Temperature rise at 115% of rated voltage: 130°C [266°F] above ambient
AC coils require external rectier