Hydraulic Valves

Description: PTS12-10N-0-80-00
Function: Directional Control Valve, 3-Way, Spool Type, Hydraulic Pilot, Internal Drain
Directional Control Valve, 3-Way, Spool Type, Hydraulic Pilot, Internal Drain 210 bar [3000 psi]• 30 I/min [8 US gpm]
This is a 3-way, spool type, hydraulically piloted directional control valve with an internal drain. In the normal condition, port 3 is connected to port 4 with port 2 blocked. Pilot pressure at port 1 will cause the valve to shift, connecting port 3 to port 2 with port 4 blocked. During the cross-over transition all ports are blocked. Due to the internal hydraulic vent, the pilot pressure required shift the valve is dependent on the pressure in port 4, which would normally be connected to tank.

Description: PTS12-10N-0-160-00
Function: Directional Control Valve, 3-Way, Spool Type, Hydraulic Pilot, Internal Drain
Directional Control Valve, 3-Way, Spool Type, Hydraulic Pilot, Internal Drain 210 bar [3000 psi]• 30 I/min [8 US gpm]
This is a 3-way, spool type, hydraulically piloted directional control valve with an internal drain. In the normal condition, port 3 is connected to port 4 with port 2 blocked. Pilot pressure at port 1 will cause the valve to shift, connecting port 3 to port 2 with port 4 blocked. During the cross-over transition all ports are blocked. Due to the internal hydraulic vent, the pilot pressure required shift the valve is dependent on the pressure in port 4, which would normally be connected to tank.

Description: 3CP2-1.5S
Function: Manual Push Valve, 2-Way, Normally Closed, Poppet Type with Check
Manual Push Valve, 2-Way, Normally Closed, PoppetType with Check 210 bar [3000 psi]• 15 I/min [4 US gpm]
This is a 2-way, normally closed, restricted, poppet type, push to open directional control valve. In the normal position, flow is blocked from 1 to 2. When the knob is manually pushed downward, port 1 is connected to port 2 through a pre-determined orifice. This valve is ideal for emergency lowering applications. It is not recommended to flow from port 2 to port 1. If this is needed, please consult the factory. 

Description: MPV1-10-K-0 
Function: Manual Pull Valve, 2-Way, Normally Closed, Poppet Type
Manual Pull Valve, 2-Way, Normally Closed, PoppetType 210 bar [3000 psi]• 45 I/min [12 US gpm] 
This is a 2-way, normally closed, poppet type, pull to open directional control valve. In the normal position, flow is blocked from 2 to 1, while free reverse flow takes place from port 1 to 2 after overcoming the spring bias. When the knob is manually pulled upward, port 1 is connected to port 2 allowing free flow in both directions. This valve is ideal for emergency lowering applications. 

Description: HLE10-OPO-2.75-B-00
Function: Logic Element, Normally Open, Spool Type, Pilot to Open
Logic Element, Normally Open, Spool Type, Pilot to Open 350 bar [S000 psi] • 60 I/min [16 US gpm] 
This is a 3-ported, normally open, pilot to open, spool type logic element. Flow is open from port 2 to port 1, until pressure in port 1 is sufficient to overcome the spring set pressure plus any pressure in port 3. The pressure in port 3 can be controlled remotely making the valve ideal for use as a normally open on/off element in a pressure reducing function. This valve is most commonly used as a pressure compensator in conjunction with a proportional directional valve. 

Description: HLE10-OPO-5.5-B-00
Function:Logic Element, Normally Open, Spool Type, Pilot to Open
Logic Element, Normally Open, Spool Type, Pilot to Open 350 bar [S000 psi] • 60 I/min [16 US gpm] 
This is a 3-ported, normally open, pilot to open, spool type logic element. Flow is open from port 2 to port 1, until pressure in port 1 is sufficient to overcome the spring set pressure plus any pressure in port 3. The pressure in port 3 can be controlled remotely making the valve ideal for use as a normally open on/off element in a pressure reducing function. This valve is most commonly used as a pressure compensator in conjunction with a proportional directional valve. 

Description: HLE10-OPO-7.5-B-00
Function:Logic Element, Normally Open, Spool Type, Pilot to Open
Logic Element, Normally Open, Spool Type, Pilot to Open 350 bar [S000 psi] • 60 I/min [16 US gpm] 
This is a 3-ported, normally open, pilot to open, spool type logic element. Flow is open from port 2 to port 1, until pressure in port 1 is sufficient to overcome the spring set pressure plus any pressure in port 3. The pressure in port 3 can be controlled remotely making the valve ideal for use as a normally open on/off element in a pressure reducing function. This valve is most commonly used as a pressure compensator in conjunction with a proportional directional valve. 

Description: HLE10-OPO-10-B-00
Function:Logic Element, Normally Open, Spool Type, Pilot to Open
Logic Element, Normally Open, Spool Type, Pilot to Open 350 bar [S000 psi] • 60 I/min [16 US gpm] 
This is a 3-ported, normally open, pilot to open, spool type logic element. Flow is open from port 2 to port 1, until pressure in port 1 is sufficient to overcome the spring set pressure plus any pressure in port 3. The pressure in port 3 can be controlled remotely making the valve ideal for use as a normally open on/off element in a pressure reducing function. This valve is most commonly used as a pressure compensator in conjunction with a proportional directional valve. 

Description: HLE10-OPO-13-B-00
Function:Logic Element, Normally Open, Spool Type, Pilot to Open
Logic Element, Normally Open, Spool Type, Pilot to Open 350 bar [S000 psi] • 60 I/min [16 US gpm] 
This is a 3-ported, normally open, pilot to open, spool type logic element. Flow is open from port 2 to port 1, until pressure in port 1 is sufficient to overcome the spring set pressure plus any pressure in port 3. The pressure in port 3 can be controlled remotely making the valve ideal for use as a normally open on/off element in a pressure reducing function. This valve is most commonly used as a pressure compensator in conjunction with a proportional directional valve. 

Description: CP701-1-B-0-170
Function: Logic Element, Normally Closed, Spool Type, Pilot to Close
Logic Element, Normally Closed, Spool Type, Pilot to Close 3S0 bar [S000 psi]• 1 SO I/min [40 US gpm] 
This is a 3-ported, normally closed, pilot to close spool type logic element. By opening port 3 to tank, flow can pass from port 1 to port 2. Flow is blocked from port 1 to port 2 unless the pressure is high enough in port 1 to overcome the spring set pressure. Applying pressure to port 3 will increase the pressure required in port 1 to open the valve by a factor of 1 to 1. This valve is ideal for use as a pressure compensator, bypass valve, or a pilot to close valve in regenerative circuits. 

Description: PSV10-NC-10-00-00-B-00
Function: Proportional Flow Control Valve, Spool Type, Normally Closed, Direct Acting, Non-Compensated
Proportional Flow Control Valve, Spool Type, Normally Closed, Direct Acting, Non-Compensated 260 bar [3800 psi]• 40 I/min [10.6 US gpm] 
This is a 2-way, spool type, normally closed, non-compensated proportional flow control valve. In the de-energized condition, flow is blocked in both directions. Energizing the coil will proportionally open port 1 to 2. Used in conjunction with a compensator, the valve will act as the control orifice for a pressure compensated flow regulator. 

Description: PSV10-NC-25-00-00-B-00
Function: Proportional Flow Control Valve, Spool Type, Normally Closed, Direct Acting, Non-Compensated
Proportional Flow Control Valve, Spool Type, Normally Closed, Direct Acting, Non-Compensated 260 bar [3800 psi]• 40 I/min [10.6 US gpm] 
This is a 2-way, spool type, normally closed, non-compensated proportional flow control valve. In the de-energized condition, flow is blocked in both directions. Energizing the coil will proportionally open port 1 to 2. Used in conjunction with a compensator, the valve will act as the control orifice for a pressure compensated flow regulator. 

Description: PSV10-NC-40-00-00-B-00
Function: Proportional Flow Control Valve, Spool Type, Normally Closed, Direct Acting, Non-Compensated
Proportional Flow Control Valve, Spool Type, Normally Closed, Direct Acting, Non-Compensated 260 bar [3800 psi]• 40 I/min [10.6 US gpm] 
This is a 2-way, spool type, normally closed, non-compensated proportional flow control valve. In the de-energized condition, flow is blocked in both directions. Energizing the coil will proportionally open port 1 to 2. Used in conjunction with a compensator, the valve will act as the control orifice for a pressure compensated flow regulator. 

Description: PSV12-NC-60-00-00-B-00
Function: Proportional Flow Control Valve, Spool Type, Normally Closed, Direct Acting, Non-Compensated
Proportional Flow Control Valve, Spool Type, Normally Closed, Direct Acting, Non-Compensated 260 bar [3800 psi] • 80 I/min [21 US gpm] 
This is a 2-way, spool type, normally closed, non-compensated proportional flow control valve. In the de-energized condition, flow is blocked in both directions. Energizing the coil will proportionally open port 1 to 2. Used in conjunction with a compensator, the valve will act as the control orifice for a pressure compensated flow regulator. 

Description: RV5-10-K-0-50/
Function: Pilot operated pressure relief valve spool type with handknob with locknut
Relief valve, Pilot operated, Spool Type 350 bar [5000 psi] • 114 l/min [30 US gpm]
This is a pilot operated, spool type relief valve that relieves from port 1 to port 2. It can be used to limit pressure in a system while maintaining accurate pressure control with constant or varying flows.

Description: CP124-1-B-0 
Load Shuttle Valve  350 bar [S000 psi] • 3.71/min [1 US gpm]
This valve senses the higher of the two input pressures at ports 1 and 3 and routes it to the output port 2

Description: SV04-00
Load Shuttle Valve  315 bar [4600 psi]• 15 I/min [4 US gpm]
This valve senses the higher of the two input pressures at ports 1 and 3 and routes it to the output port 2.

Description: 1SH10
Load Shuttle Valve, Insert type 3S0 bar [S000 psi] • 20 I/min [S US gpm]
This valve senses the higher of two input pressures at 1 and 3, and routs it to output 2. 

Description:  CP240-5-B-0-E-C-XXX
Function: Sequence Valve, Normally Open, Spool Type, Hydraulic Pilot, External Drain
Sequence Valve, Normally Open, Spool Type, Hydraulic Pilot, External Drain 210 bar [3000 psi]• 25 I/min [7 US gpm] 
This is a hydraulically pilot operated spool valve, normally open from port 2 to 3 with port 4 as a drain port connected to tank. When the pilot pressure on port 1 reaches the setting, the valve will begin to close port 2 to 3. This is ideal for sensing pressure in a remote area of a circuit to sequence another operation. 

Description: PSV10-10-S-0-24
Function: Sequence Valve, Normally Closed, Spool Type, Hydraulic Pilot, External Drain
Sequence Valve, Normally Closed, Spool Type, Hydraulic Pilot, External Drain 210 bar [3000 psi]• 23I/min [6 US gpm] 
This is a hydraulically pilot operated spool valve, normally closed from port 2 to 3 with port 4 as a drain port connected to tank. When the pilot pressure on port 1 reaches the setting, the valve will begin to open port 2 to 3. This is ideal for sensing pressure in a remote area of a circuit to sequence another operation

Description: 1PS100P20S 
Function: Sequence Valve, Pilot Operated, Spool Type, Internal Pilot, External Drain
Sequence Valve, Pilot Operated, Spool Type, Internal Pilot, External Drain 
3S0 bar [S000 psi]• 1S0 I/min [40 US gpm] 
This is a pilot operated, spool type sequence valve that opens from port 1 to port 2 when the setting is reached. This is ideal for sequencing a secondary operation while maintaining pressure in the primary operation, limiting pressure loss with constant or varying flows. 

Description: 1PSC100P20S
Function: Sequence Valve, Pilot Operated, Poppet Type with Reverse Free Flow, Internal Pilot, External Drain
Sequence Valve, Pilot Operated, PoppetType with Reverse Free Flow, Internal Pilot, External Drain 350 bar [S000 psi]• 1S0 I/min [40 US gpm] 
This check. is a It pilot opens from operated, port 1 poppet to port type 2 when sequence the set valve pressure with a is reverse reached flow and free flows from port 2 to 1. It  can be directional used to valve, sequence where free operations flow is in a necessary system or in in the a service reverse line direction.

Description: 1PSC100P35S
Sequence Valve, Pilot Operated, PoppetType with Reverse Free Flow, Internal Pilot, External Drain 350 bar [S000 psi]• 1S0 I/min [40 US gpm] 
This check. is a It pilot opens from operated, port 1 poppet to port type 2 when sequence the set valve pressure with a is reverse reached flow and free flows from port 2 to 1. It  can be directional used to valve, sequence where free operations flow is in a necessary system or in in the a service reverse line direction.

Description: RPC04-5-OR-00 
Check valve, Standard Direction 350 bar [5000psi] - 21/min [5.5 US gpm] 
Description and operation: this is a Check valve where free flow takes place from port 2 to 3 and is blocked from port 3 to 2.